rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 1 (4) stand juni 2016 rev 01 1) these are stress ratngs. exposure of devices to any of these conditons may adversely afect long-term reliability. 2) (1.5mm from case 10sec max.) 3) all specifcatons typical at ta= 25c, nominal input voltage and full load unless otherwise specifed. 4) the informaton and specifcaton contained in this data sheet are believed to be correct at tme of publicaton. however rsg accepts no responsibility for consequences arising from printng errors or inaccuracies. specifcatons are subject to change without notce. dc/dc-converter rr6-s05/d05 5.0w 4:1 regulated single & dual output we energize electronics! an acal group company we energize electronics! ? 24 pin dil package ? wide 4:1 input range ? 1500vdc isolaton ? up to 3500vdc isolaton ? contnuous short circuit protecton ? efciency up to 83% ? operatng temperature range -40 ~ +85c ? metal case standard , optonal plastc case output specification voltage accuracy: 1% line regulaton: single &dual 0.5% max. load regulation: 0.5% output 3.3v model: 1.5% short circuit protecton : indefnite (automatc recovery) ripple noise (20mhz bandwidth): 60mv pk-pk temperature coefcient: 0.02% c capacitor load: see table input specifications voltage range: see table max. input current: see table no-load/full-load input current: see table input filter: pi type input refected ripple current : 35ma pk-pk general specifications efciency: see table typ. i/o isolaton voltage metal case (3 sec.): 1000vdc i/o isolaton voltage (3 sec.): 1500 ~ 3500vdc i/o isolaton capacitance: 470pf typ. i/o isolaton resistance: 1000m ohm switching frequency: 266khz, typ. humidity: 95% rel h reliability calculated mtbf : > 1.21mhrs (mil-hdbk-217 f) safety standard: (designed to meet): iec 60950-1 environmental specification operatng temperature range: -40c ~+85c (see deratng curve) maximum case temperature: 100c storage temperature : -40c ~+125c cooling : nature convecton physical specifications: case material: nickel-coated copper base material: non-conductve black plastc (ul94v-0 rated) pin material: ? 0.5mm brass solder coated potng material: epoxy (ul94v-0 rated) weight case-dip: 13.5g (plastc), 17.0g ( metal) dimmension dip: 1.25 x 0.8 x 0.4 absolute maximum ratings (1) input surge voltage (100ms)/ 24v models: 40vdc max. 48v models: 80vdc max. soldering temperature: 260c max. (2) emc specifications radiated-/conducted emissions: en55022 class a (see emi filter note) esd: iec 61000-4-2 perf.criteria a rs: iec 61000-4-3 perf.criteria a eft: iec 61000-4-4 perf.criteria a surge: iec 61000-4-5 perf.criteria a cs: iec 61000-4-6 perf.criteria a pfmf iec 61000-4-8 perf.criteria a rohs
rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 2 (4) stand juni 2016 rev 01 r r 6 - xx xx s/d xx power (w) input t ype a x x code inter nal isolation (kvdc) dc/dc-converter -/d ete ne d tt we energize electronics! an acal group company we energize electronics! model selection guide model number in p ut volt age range (vdc) inpu t current output vol tage (vd c) output current efficie ncy @fl (%) capacitor o load ( ) fu lo ad () i oa d () fu oa d () load (uf) 3.3 0 757 74 100 rr6 - 240 5 d05ax 9 - 36 18 260.4 5 0 500 80 100 rr6 - 24 07d05ax 9 - 36 18 257.2 7.2 0 347 81 100 rr6 - 240 9 d05ax 9 - 36 20 257.2 9 0 277 81 100 rr6 - 241 2 d05ax 9 - 36 20 251.0 12 0 208 83 68 rr6 - 241 5 d05ax 9 - 36 20 260.4 15 0 166 80 22 rr6 - 242 4 d05ax 9 - 36 26 263.7 24 0 104 79 22 rr6 - 48 03s05ax 18- 72 15 119.2 3.3 0 1300 75 1000 rr6 - 48 05 s05ax 18- 72 15 130.2 5 0 1000 80 1000 rr6 - 48 07s05ax 18- 72 15 127.0 7.2 0 694 82 1000 3.3 0 757 78 680 rr6 - 480 5 d05ax 18- 72 15 130.2 5 0 500 80 330 rr6 - 48 07d05ax 18- 72 15 130.2 7.2 0 347 80 100 rr6 - 480 9 d05ax 18- 72 15 127.0 9 0 277 82 100 rr6 - 481 2 d05ax 18- 72 15 127.0 12 0 208 82 100 rr6 - 481 5 d05ax 18- 72 15 130.2 15 0 166 80 47 rr6 - 482 4 d05ax 18- 72 15 131.8 24 0 104 79 22 suffix ? 3 ? means 3.5kvdc isolation suffix ?p? means plastic case instead of standard metal case the models listed above is just for standard type. if you need the special specification product, please contact our service member by telephone presented in shortform cover or e - mail t o : info@ rsg - electronic.de
rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 3 (4) stand juni 2016 rev 01 +vout +vin dc/dc converter - vin - vout test configurations output ripple & noise measurement test copper strip +vout use a capacitor cout(1.0uf) measurement. the scope measurement bandwidth is 0 - 20mhz. single dc/dc converter 1uf cout resistive scope load - vout input reflected ripple current test step input reflected ripple current is measured through a source inductor lin(12uh) and a source capacitor cin(47uf, esr<1.0 at 100khz) at nominal input and full load. lin current probe cin load emi filter +vout +vin input filter components (c1,c3, l) are used to help meet conducted emissions requirement for the module. these components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. l dc/dc converter load c1 - vin - vout c3 c1 l c3 220uf, 100v 12uh 1000pf,2kv note 1. ripple/noise measured with a 1uf ceramic capacitor. 2. t es t by nominal input voltage and constant resistor load. 3. measured input reflected ripple current with a simulated source inductance of 12uh. 4. exceeding the absolute ratings of the unit could cause damage. it is not allowed for continuous operating. 5.it?s recommended to add c1(220 u f), c3(1000p f ,2kv) , l(12 u h) in input end to achieve en55022 conducted class a. 6.an external filter capacitor is required if the module has to meet iec 61000- 4 - 5. the filter capacitor rsg suggest: nippon - chemi - con ky series, 220uf/100v. lo line nominal hi line efficiency vs output current 90 85 80 75 70 65 60 55 50 0% 20% 40% 60% load 80% 100% 120% efficiency vs output current 90 85 80 75 70 65 60 55 50 lo line nominal hi line 0% 20% 40% 60% load 80% 100% 120% electrical characteristic curves 2 4 models 4 8 models efficiency(%) efficiency(%) +vout +vin dc/dc converter - vin - vout test configurations output ripple & noise measurement test copper strip +vout use a capacitor cout(1.0uf) measurement. the scope measurement bandwidth is 0 - 20mhz. single dc/dc converter 1uf cout resistive scope load - vout input reflected ripple current test step input reflected ripple current is measured through a source inductor lin(12uh) and a source capacitor cin(47uf, esr<1.0 at 100khz) at nominal input and full load. lin current probe cin load emi filter +vout +vin input filter components (c1,c3, l) are used to help meet conducted emissions requirement for the module. these components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. l dc/dc converter load c1 - vin - vout c3 c1 l c3 220uf, 100v 12uh 1000pf,2kv note 1. ripple/noise measured with a 1uf ceramic capacitor. 2. t es t by nominal input voltage and constant resistor load. 3. measured input reflected ripple current with a simulated source inductance of 12uh. 4. exceeding the absolute ratings of the unit could cause damage. it is not allowed for continuous operating. 5.it?s recommended to add c1(220 u f), c3(1000p f ,2kv) , l(12 u h) in input end to achieve en55022 conducted class a. 6.an external filter capacitor is required if the module has to meet iec 61000- 4 - 5. the filter capacitor rsg suggest: nippon - chemi - con ky series, 220uf/100v. lo line nominal hi line efficiency vs output current 90 85 80 75 70 65 60 55 50 0% 20% 40% 60% load 80% 100% 120% efficiency vs output current 90 85 80 75 70 65 60 55 50 lo line nominal hi line 0% 20% 40% 60% load 80% 100% 120% electrical characteristic curves 2 4 models 4 8 models efficiency(%) efficiency(%) 1. ripple/noise measured with a 1uf ceramic capacitor. 2. t es t by nominal input voltage and constant resistor load. 3. measured input reflected ripple current with a simulated source inductance of 12uh. 4. exceeding the absolute ratings of the unit could cause damage. it is not allowed for continuous operating. 5.it?s recommended to add c1(220 u f), c3(1000p f ,2kv) , l(12 u h) in input end to achieve en55022 conducted class a. 6.an external filter capacitor is required if the module has to meet iec 61000- 4 - 5. the filter capacitor rsg suggest: nippon - chemi - con ky series, 220uf/100v. lo line nominal hi line efficiency vs output current 90 85 80 75 70 65 60 55 50 0% 20% 40% 60% load 80% 100% 120% efficiency vs output current 90 85 80 75 70 65 60 55 50 lo line nominal hi line 0% 20% 40% 60% load 80% 100% 120% electrical characteristic curves 2 4 models 4 8 models efficiency(%) efficiency(%) dc/dc-converter rr6-s05/d05 5.0w 4:1 regulated single & dual output we energize electronics! an acal group company we energize electronics! test configurations electrical characteristic curves
rsg electronic components gmbh ?sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ?rsg-electronic.de page 4 (4) stand juni 2016 rev 01 mechanical specifica tions 31.75 (1.25) 20.32 (0.80) 10.16 (0.40) 3.00 (0.12) printed face 24 pin dil package non-conductive plastic dc-dc conver ter xxxx pin connections pin number single-h dual-h 1 1 2 2 1 3 9 1 5 3 1 4 1 0 1 6 1 1 2 2 single +v input +v input v input v input v input +v output n.p. +v output +v output +v output v output n.p. v output v output common n.c. n.c. n.c. n.c. -v input n.p. n.p. n.p. +v output dual +v input n.p. +v input -v input +v input v output common common common common v input +v output +v input n.p. n.p. n.c. n.p. n.p. v input v output v input n.p. 2 3 2 4 v output n.p. common +v input +v input n.p. n.p. n.p. n.p. n.p. for ?p? case 0.50 (0.02) 5.08 (0.20) 15.24 (0.60) 0.50 (0.02) 22.86 (0.9) bottom v iew 1 2 3 9 10 11 12 24 23 22 16 15 14 13 notes: all dimensions are typical in millimeters ( inches ). 1. pin diameter: 0.5 0.05 ( 0.02 0.002 ) 2. pin pitch tolerance: 0.35 ( 0.014 ) 3. case tolerance: 0.5 ( 0.02 ) and length pin connections pin number single-h dual-h 1 1 2 2 1 3 9 1 5 3 1 4 1 0 1 6 1 1 2 2 single +v input +v input v input v input v input +v output n.p. +v output +v output +v output v output n.p. v output v output common n.c. n.c. n.c. n.c. -v input n.p. n.p. n.p. +v output dual +v input n.p. +v input -v input +v input v output common common common common v input +v output +v input n.p. n.p. n.c. n.p. n.p. v input v output v input n.p. 2 3 2 4 v output n.p. common +v input +v input n.p. n.p. n.p. n.p. n.p. bottom view 3 1 . 7 5 ( 1 . 25) 2 0 . 3 2 ( 0 . 80) 2 7 . 9 4 ( 1 . 1 0 ) 0 . 5 0 ( 0 . 0 2 ) 2 . 5 4 ( 0 . 1 0 ) dia 0 . 5 0 ( 0 . 02) 1 5 . 2 4 ( 0 . 6 0 ) built - i n stand - o s hel p a i r convecti o n p r i nted face 1 0 . 1 6 ( 0 . 4 0 ) 3 . 0 0 ( 0 . 1 2 ) dc-dc conver ter xxxx 24 pin dil package nickel-coated copper 1 2 3 9 10 1 1 12 15 14 13 24 23 22 16 notes: all dimensions are typical in millimeters ( inches ). 1. pin diameter: 0.5 0.05 ( 0.02 0.002 ) 2. pin pitch tolerance: 0.35 ( 0.014 ) 3. case tolerance: 0.5 ( 0.02 ) and length rr6-xxxxs05a1 rr6-xxxxs05a1p dc/dc-converter rr6-s05/d05 5.0w 4:1 regulated single & dual output e enegie electonic an acal goup copan e enegie electonic mechanical specifications the models listed here are just standard type. if you need a product with special specifcaton or you have questons regarding packing standards (tube oder tape/reel) as well as applicaton support, please contact our specialists: sales @ rsg-electronic.de or +49 69-984047-41/-28
|
